Welcome to Polymer Racing Products.
We are grass roots racers and engineers, developing products from the bottom up specifically for the drag racing community. We design, prototype, test, and manufacture our products in USA and Canada.
We are grass roots racers and engineers, developing products from the bottom up specifically for the drag racing community. We design, prototype, test, and manufacture our products in USA and Canada.
International Dyno Authority independently tests our 1" 4150 dimpled spacer. Shocked when the dyno shows 21Hp on top of a very popular spacer they tested, for a total of 35Hp. Watch the YouTube video by clicking here.
Polymer Racing Products spacers feature aluminum sleeves in the mounting holes for improved strength.
Polymer Racing Products very own Adam Bitzanis wins Super Tour Bracket Bonanza at Luskville. "The PRP Thumb Gate was once again key to consistent reaction times helping me take the win."
Polymer Racing Products very own Adam Bitzanis takes the 2020 S/Pro Dragster National Champion.
"The PRP1008 Thumb Gate was key to consistent reaction times helping me take the 2020 title."
"The PRP1008 Thumb Gate was key to consistent reaction times helping me take the 2020 title."
Below is Chris Bowen's 1965 Dodge Dart 572ci all aluminum 970 HP engine featuring a Polymer Racing Product SV1 cloverleaf spacer with Dimple Technology sitting on a Indy 440-3x full port intake.
Below is Dan's Dragster spotted at Naperville drag way sporting a Polymer Racing Product 4500 Series Carb Spacer with Dimple Technology.
Consistent reaction times, require consistency on where your place your thumb on the transbrake button. The Polymer Racing Products "007 Thumb Gate" shown below does just that. It aligns your thumb on the transbrake button at the same position every time for consistent reaction times.
Below is the PRP1008 Thumb Gate designed to fit over the Biondo Double O Transbrake button.
Below is the PRP1008 Thumb Gate designed to fit over the Biondo Double O Transbrake button.
Images below show the worlds first carburetor spacer featuring Dimple Technology. Watch the YouTube video of the dyno run and check the 4500 Carb Spacer page for more details.
Testimonial below from Dan at KB Performance in NY.
"We installed your 4500 carb spacer 1 inch thick on our 540 inch bbc on gas we had a 12 hp gain at 6400 with no changes over the hvh 1 inch super sucker Thank you for a great product we will be changing all of the spacers on our cars. Keep up the good work."
"Just wanted to let you know we tried part number prp1005 [1" 4500] spacer on our aluminum headed 355 sbc we use in the super street nova on the dyno we picked up on the average 8 horse power and 5 lbs of torque consistently from 5000 to 7200 over the 1 inch aluminum hvh spacer with no other changes. Thanks again."
KB Performance Center
Karyl Bell Viscione
Dan Bell
"Just wanted to let you know we tried part number prp1005 [1" 4500] spacer on our aluminum headed 355 sbc we use in the super street nova on the dyno we picked up on the average 8 horse power and 5 lbs of torque consistently from 5000 to 7200 over the 1 inch aluminum hvh spacer with no other changes. Thanks again."
KB Performance Center
Karyl Bell Viscione
Dan Bell
Testimonial below from a customer of the belt drive cover.
"Like I said, this thing [Belt Drive Cover] has saved me a couple of times. Before when I had a leak (pushed out front intake seal) I would sweat it at the track until I got home then swap to a new $110 belt. Since I put it on had at least two occasions (blower snout seal and front intake seal) push out covering the front of the motor with oil, not a drop got under the cover on the belt. Wiped everything down and good to go. I’m sure it’s protecting the belt from rocks and such judging by the occasional chunks in the blower belt."
Keith Neimann
Keith Neimann
Product: Belt Drive Cover